ABSTRACT In this paper a comparison of mix design procedures of IS method - Concrete mix proportioning guidelines (Bureau of Indian Standards-I.S.10262-2009),BS method (17-7 Stainless Steel Technical Data SheetThe 17-7 alloy is a chromium-nickel-aluminum precipitation hardening stainless steel used for applications requiring high strength and a moderate level of corrosion resistance.The 17-7 alloy has been available for many years and has found application in aerospace and many spring type applications requiring high strength.AISI 316 Stainless Steel Properties,SS 316 Grade Density SS 316 is better than SS 304 in terms of corrosion resistance,heat resistance and certain properties,but the price is higher than AISI 304,for more details,please check stainless steel grade 304 vs 316,and 316 vs 316L.SS 316 Data Sheet Specification
·Greater tensile strength at higher operating temperatures; Acidic resistance of solutions of nitric acid of concentration as high as 5% at 50 o C; Phosphoric acid of concentration of up to 20% at 100 o C; In comparison,the SS AISI 316 boasts better resistance to chloride-rich conditions than the typical SS 304 thanks to the molybdenum addition.All About 304 Steel (Properties,Strength,and Uses)The density of 304 steel is around 8 g/cm 3,or 0.289 lb/in 3.Type 304 steel also comes into three main varieties 304,304L,and 304H alloys,which chemically differ based on carbon content.304L has the lowest carbon percentage (0.03%),304H has the highest (0.04-0.1%),and balanced 304 splits the difference (0.08%).In general,304L is reserved for large welding components that do not require postAmerican Standard I-Beams McMaster-CarrMade of rigid low-carbon steel,these I-beams are often used in construction,framing,lifting,and hoisting applications.Also known as mild steel,low-carbon steel is the most commonly used material for I-beams.It deflects less under load than medium- or high-carbon steel and is less likely to crack from welding.These I-beams have rounded corners,and are also known as American Standard I
Behavior and Design of High-Strength Constructional Steel presents readers with extensive information on the behavior of high-strength constructional steels,providing them with the confidence they need to use them in a safe and economic manner to design and construct steel structures.The book includes detailed discussions on the mechanical properties of HHS while explaining the latest Comparing American and British Piping StandardsA312 Gr.Tp 304 3605/304 S18 (EN58E) Austenitic chromium nickel A312 Gr.Tp 304H 3605/304 S59 Austenitic chromium nickel A312 Gr.Tp 304L 3605/304 S14 Austenitic chromium nickel (extra low carbon) A312 Gr.Tp 316 3605/316 S18 (EN58J) Austenitic chromium nickel molybdenum bearing A312 Gr.Tp 316L 3605/316 S14Fastener Identi cation Markings ASTM,SAE,ISOYield Strength Min (psi) Tensile Strength Min (psi) B8 ASTM A193Grade B8 Bolts,Screws,Studs for High-Temperature Service AISI 304Strain Hardened 1/4 thru 3/4 Over 3/4 thru 1 Over 1 thru 1-1/4 Over 1-1/4 thru 1-1/2 100,000 80,000 65,000 50,000 125,000 115,000 105,000 100,000 B8C ASTM A193Grade B8C AISI 347Strain Hardened B8M ASTM
Strength Strength reduction provisions (Section A2.3.2) are introduced for high-strength and low-ductility closed-box section members.Elements The effective width equation (Eq.B2.2-2) for uniformly compressed stiffened elements with circular holes has been revised.SS304 Grade AISI 304 Stainless Steel Properties ·K-Alloy/A304 is a patented casting aluminum alloy introduced in 2003 and has been a game-changer for manufacturers as it eliminates the need forSTAINLESS STEEL SUGGESTED PRACTICES FORstandard by the American Iron and Steel Institute. 302,304,301 and 316,with Types 201 and 202 also available.All six have excellent corrosion re sistance,high strength and ease of fabrication.AISI Type 302,the original 18-8 alloy (18% chromium,8% nickel),is most often specified for
In this Specification,the term lot shall be taken as that given in the ASTM Standard as follows Product ASTM Standard See Lot Definition in Section Bolts A325 9.4 A490 11.3.2 or 11.4.2 Twist-off-type tension control bolt assemblies F1852 13.4 Nuts A563 9.2 Washers F436 9.2 Compressible-washer-type direct tension indicators F959 10.2.2 Steel-Clad Steel Wire (ACS wire) and Steel Clad A high strength steel wire with a 25% thick cross-section ratio of aluminum cladding creating a high electrical conductivity,highly corrosive resistant and a thermal stability for high temperature operation and all with a lighter weight. American Standard ACS Cable .
ASTM A193 Grade B7 is the specification for high strength,heat resistant American Iron and Steel Institute (AISI) 4140 alloy steel threaded rod.The versatile B7 threaded rod is in high demand because of its high strength,excellent heat resistance and resistance to corrosion. (304 stainless steel) and grade B8M (316 stainless steel) are Transmissions Chains - Roller Chains Wholesale Distributor American Standard Chains are fabricated with the latest mechanical devices and the finest quality raw materials that are procured from the trusted vendors of the industry.Known for their high durability,accurate dimensions and sturdiness,these products are widely used in various industrial applications.